Fanúšikovia počítača fungujú vždy na 100%, ak nie sú uvedené inak?

Obsah:

Fanúšikovia počítača fungujú vždy na 100%, ak nie sú uvedené inak?
Fanúšikovia počítača fungujú vždy na 100%, ak nie sú uvedené inak?

Video: Fanúšikovia počítača fungujú vždy na 100%, ak nie sú uvedené inak?

Video: Fanúšikovia počítača fungujú vždy na 100%, ak nie sú uvedené inak?
Video: TOP 10 Tajné funkce mobilu o kterých 90% lidí neví - YouTube 2024, Apríl
Anonim
Či už na prenosných počítačoch, stolných počítačoch alebo dokonca v herných konzolách, všetci sme počuli v pozadí záblesky systémových fanúšikov. Ako presne všetci títo malí fanúšikovia vedia, kedy sa točia, dolu a inak umiernia množstvo vzduchu, ktoré sa pohybujú?
Či už na prenosných počítačoch, stolných počítačoch alebo dokonca v herných konzolách, všetci sme počuli v pozadí záblesky systémových fanúšikov. Ako presne všetci títo malí fanúšikovia vedia, kedy sa točia, dolu a inak umiernia množstvo vzduchu, ktoré sa pohybujú?

Dnešná relácia otázok a odpovedí sa k nám dostala s láskavým združením oddeleniu SuperUser - rozdelenie Stack Exchange, skupiny komunitných skupín otázok a odpovedí.

Otázka

Čítačka SuperUser darkAsPitch sa pýta:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

Tak ako fungujú? Úplný vývrt, pokiaľ nie je príkazom inak?

Odpoveď

Príspevok SuperUser Journeyman Geek ponúka tento pohľad:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

Spolupracovník Hyperslug zdôrazňuje, ako výnimky hrajú:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

A tu ho máte: mimo vonkajšej kontroly pomocou nejakého mechanizmu (či už je to vstup na základnej doske, teploměr alebo inteligentný PSU), ventilátory budú pracovať s najvyššou rýchlosťou, ktorú napájací zdroj dovolí.

Máte niečo doplniť vysvetlenie? Zvuk vypnúť v komentároch. Chcete si prečítať viac odpovedí od iných používateľov technológie Stack Exchange? Pozrite sa na celý diskusný príspevok tu.

Odporúča: