Existuje kvantifikovateľný dôkaz pre silový cyklus routeru na 10 sekúnd?

Obsah:

Existuje kvantifikovateľný dôkaz pre silový cyklus routeru na 10 sekúnd?
Existuje kvantifikovateľný dôkaz pre silový cyklus routeru na 10 sekúnd?

Video: Existuje kvantifikovateľný dôkaz pre silový cyklus routeru na 10 sekúnd?

Video: Existuje kvantifikovateľný dôkaz pre silový cyklus routeru na 10 sekúnd?
Video: How can I control all my connected home devices from one app? - YouTube 2024, Marec
Anonim
Všetci sme počuli rady o napájaní elektrickým prúdom s elektronickým zariadením, aby sme vyriešili problémy, ale je lepšie, než jednoducho odpojiť a zapojiť zariadenie späť? Dnešný príspevok SuperUser Q & A má odpovede na otázku zvedavého čitateľa.
Všetci sme počuli rady o napájaní elektrickým prúdom s elektronickým zariadením, aby sme vyriešili problémy, ale je lepšie, než jednoducho odpojiť a zapojiť zariadenie späť? Dnešný príspevok SuperUser Q & A má odpovede na otázku zvedavého čitateľa.

Dnešná relácia otázok a odpovedí sa k nám pridelí zdvorilosťou SuperUser - podskupiny Stack Exchange, skupín webových stránok týkajúcich sa otázok a odpovedí.

Foto s láskavým dovolením Ben Daines (Flickr).

Otázka

Nástroj na čítanie súborov SuperUser chce zistiť, či existujú nejaké kvantifikovateľné dôkazy na podporu elektronických zariadení s napájaním elektrickým prúdom namiesto toho, aby ste ich jednoducho odpojili a pripojili ich späť:

Is there any quantifiable evidence to support power cycling routers for 10 seconds (or any arbitrary amount of time) instead of just unplugging and plugging them back in?

This is related to troubleshooting a misbehaving router. The theory is based on ‘things’ needing to be cleared from memory and that this could take a few seconds. This is also a theory related to electronics from over a decade ago, and I am sure it was equally as anecdotal then.

As a person allergic to anecdotes, I became curious when I realized that I had never investigated this issue. Is there any quantifiable reason to support power cycling routers for 10 seconds (or any arbitrary amount of time) instead of just unplugging and plugging them back in?

Existujú nejaké kvantifikovateľné dôkazy na podporu elektronických zariadení s elektrickým cyklom versus jednoduché odpojenie / opätovné pripojenie?

Odpoveď

Sponzori SuperUser Enis P. Aginic a Wes Sayeed majú odpoveď pre nás. Prvýkrát, Enis P. Aginic:

Yes, there is. Any electronics device will have capacitors that will store energy even after you unplug it. You may have noticed that when you unplug a monitor or TV, the little diode will take another second or two to discharge remaining energy from the capacitors in the form of electricity and stop glowing.

This residual energy may not allow memory chips to wipe and you may have problems once your router starts again.

As for sources, well it is really common sense to someone with basic electronics knowledge, like the sky is blue and water is wet, so I recommend reading about capacitors to see what they do and you will understand it.

The point is that electronics components are far from perfect and any interference may produce unpredictable results.

Nasledovala odpoveď od Wesa Sayeeda:

Ten seconds is an arbitrarily long amount of time, but yes, it does take time for electronic devices to discharge themselves completely because of the capacitance of the circuits within. Some of this capacitance is intentional, some of it is not.

It is impossible to say exactly how much time is needed, as the bleed-off of that capacitance varies with environmental factors like temperature, humidity, and background EMI generated by nearby electronics. The RAM in your computer, for example, can take minutes to fully discharge.

But there is a shortcut. If the router has a button of any kind on it (WPS button or a reset button), this will usually discharge any residual electrical charge immediately. This is because the button places a load on the circuit(s) holding the charge and there is no power going into the device.

In fact, in the old days of parallel ports, this used to be a guaranteed way to correct a stubborn printer. Unplug the printer, unplug the computer, and unplug the parallel cable. Then hit the power button on both devices. Then plug everything back in. Worked every time. Parallel SCSI busses had this problem too sometimes.

Máte niečo doplniť vysvetlenie? Znížte komentáre. Chcete si prečítať viac odpovedí od iných používateľov technológie Stack Exchange? Pozrite sa na celý diskusný príspevok tu.

Odporúča: